AK/SKS Accessories

• Fits Stamped AK Receivers
• Will not fit on AK variants with a milled receiver, a bottom tang, a slant-cut receiver at the rear, or an underfolder stock
• Will not fit MAK 90
• Counts as 1 U.S. 922r Compliant Part
• Item Includes:
  - T6™ Stock Body
  - AK 6 Position Stock Tube for Stamped AK Receivers
  - Side Sling Attachment
• Lengh of Pull:
  - 10.5" (fully collapsed)
  - 11.25"
  - 12.25"
  - 13"
  - 13.75"
  - 14.5" (fully extended)

• Will not work on Saiga rifles and shotguns with an angled rear receiver
• Due to the angled trigger on the Saiga .308, the addition of this stock may create a less ergonomic trigger pull.
• Counts as 2 U.S. Sec 922r Compliant Parts (buttstock and pistol grip)
• Package Includes:
  - TAPCO T6 Collapsible Stock
  - TAPCO Rubber Buttpad
  - TAPCO SAW Style Pistol Grip
  - TAPCO Straight 6 Position Stock Tube
  - Side Sling Attachment
• Length of Pull:
  - 10.875" (fully collapsed)
  - 11.625"
  - 12.375"
  - 13.25"
  - 14.125"
  - 14.75" (fully extended)

• Holds 20 rounds of 7.62 x 39mm ammunition
• Designed for use in the AK-47
• Anti-Tilt Follower
• Double Stack
• Heavy Duty Spring
• Body Constructed of Reinforced Composite
• Counts as 3 U.S. 922r Compliant Parts (body, floorplate, follower)

Looking for a rugged and reliable low capacity AK mag? The INTRAFUSE® 5rd AK-47 Magazine is your answer. The reinforced composite material prevents corrosion while the heavy duty spring and anti-tilt follower ensure that every round will feed perfectly. Fits the AK-47 using 7.62 x 39mm ammunition. Not to mention that it counts as 3 U.S. 922r compliant parts..

• Holds 30 rounds of 5.45 x 39mm ammunition
• Designed for use in the AK-74
• Anti-Tilt Follower
• Double Stack
• Heavy Duty Spring
• Body Constructed of Reinforced Composite
• Will not work in a Saiga without modification to the rifle
• Counts as 3 U.S. 922r compliant parts (body, follower, floorplate)

Due to the varying sizes of factory SKS pistons, your factory piston may or may not have a proper fit with this gas tube. In some cases, a TAPCO® replacement gas piston must be purchased as well.

Due to the varying sizes of factory SKS pistons, your factory piston may or may not have a proper fit with this gas tube. In some cases, a TAPCO® replacement gas piston must be purchased as well.

• This item may require modifications (that will void the warranty) to fit the MAK-90
• Counts as 1 U.S. 922r Compliant Part
• Item Includes:
  - Upper Handguard with Attached Picatinny Rail
  - Lower Handguard with Molded-In Lower Picatinny Rail, 2 Pre-Installed Side Rails, and a Heat Shield
  - Lower Rail Cover

• Holds 30 rounds of 7.62 x 39mm ammunition
• Designed for use in the AK-47
• Double Stack
• Anti-Tilt Follower
• Heavy Duty Spring
• Body Constructed of Reinforced Composite
• Counts as 3 U.S. 922r Compliant Parts (body, floorplate, follower)

• Designed for use on AK's with a standard left hand threaded barrel
• 14 x 1 LH Thread Pitch
• Manufactured From Steel
• Manganese Phosphate Finish
• 100% U.S. Made
• Counts as 1 U.S. 922r Compliant Part

• Designed for use on AK's with a standard left hand threaded barrel
• 14 x 1 LH Thread Pitch
• Manufactured From Steel
• Manganese Phosphate Finish
• 5 Retention Pin Catches
• Counts as 1 U.S. 922r Compliant Part

If you like the look of the traditional M16 birdcage but you’re an AK owner, this is the item you’ve been waiting for. Designed to replicate the M16 flash hider, this AK muzzle device is a beefed-up version engineered to withstand the muzzle blast from the more powerful 7.62x39mm rounds. Quality machined threads and multiple locking tabs make this muzzle attachment a breeze to install.

MFR# AK0685

UPC: 0751348005898

• Four heat threaded pronged tips
• Length = 2.8125"
• Fits standard 14 x 1 left hand threaded AK Models
• Counts as 1 U.S. 922r Compliant Part