PSA 10.5" Carbine-Length 5.56 NATO 1/7 Nitride 12" Slant M-Lok MOE EPT SBA3 Pistol Kit - 5165448877

More Views

PSA 10.5" Carbine-Length 5.56 NATO 1/7 Nitride 12" Slant M-Lok MOE EPT SBA3 Pistol Kit - 5165448877

TEMPORARILY OUT OF STOCK

Quick Overview

free shipping Free Shipping applies to this item only and not the entire order.

It is the customer's responsibility to be aware of all applicable laws and regulations regarding the purchase and ownership of uppers with a barrel length of less than 16". Federal NFA regulations are applicable to this item.

WARNING: Handling firearms or firearms parts can expose you to lead and other petroleum products known to the State of California to cause cancer, birth defects, or other reproductive harm. Wash hands thoroughly after handling. For more information go to www.p65warnings.ca.gov (CA Health and Safety Code Section 25249.6).

SKU: 5165448877
UPC: 5165448877
MFR#: 5165448877

Barrel Length: 10.5"
Barrel Profile: A2
Gas System: Carbine-Length
Barrel Steel: 4150V Chrome Moly Vanadium
Barrel Finish: Nitride
Chrome Lining: No
Muzzle Thread: 1/2x28
Chamber: 5.56 NATO 
Twist Rate: 1:7
Barrel Extension: M4
Diameter at Gas Block: .750
Gas Block Type: Low-profile
Muzzle Device: PSA Fluted Flash Can
Receiver Material: Forged 7075 T6 Aluminum
Receiver Type: M4
Handguard Type: PSA 12" Slant End M-Lok Rail
Bolt Carrier Group Included: Yes
Bolt Steel: Carpenter 158
Bolt Carrier Profile: Full-auto
Charging Handle Included: Yes
Overall Length: 21"
Build Kit: MOE SBA3 EPT Pistol Kit, Black

Add To:

Barrel: 10.5" 4150V Chrome Moly vanadium steel, nitride treated for accuracy and durability, and chambered in 5.56 NATO with a 1 in 7" twist. Carbine-length gas barrel is finished off with a PSA 12" Slant End M-Lok Rail, a low profile gas block and a PSA Fluted Flash Can.

Upper: Forged 7075-T6 A3 AR upper is made to MIL-SPECS and hard coat anodized black for durability. Featuring a mil-spec finish, these uppers are made for us right here in the USA by a mil-spec manufacturer.

Flash Can: Palmetto State Armory's Fluted "FLASH CAN". This is a solid 6061 aluminum device that is designed to direct muzzle gases and the muzzle flash forward. Threaded 1/2x28 for 5.56 NATO. Black military-style hard anodizing. THIS DEVICE IS NOT DESIGNED TO REDUCE RECOIL, MUZZLE RISE, OR FLASH SIGNATURE. This device is designed to direct gasses and noise forward away from the shooter and enhance the weapon's appearance.

Bolt: Bolt is made of Mil-spec shot-peened Carpenter 158 steel. Gas key is secured with grade 8 fasteners and staked per mil-spec. 

Build Kit: A high quality lower build kit with everything you need to assemble your AR-15 lower into a pistol. Features Enhanced Polished Trigger (EPT), Magpul Grip, Magpul Trigger Guard, and black oxide coated hammer and trigger springs. Also includes SB Tactical SBA3 Adjustable Pistol Brace, castle nut, latch plate, carbine buffer spring, 5 positioning mil-spec buffer tube, and standard carbine buffer.

SKU: 5165448877
SKU 5165448877
Brand Palmetto State Armory
Department Uppers
Daily Deal No
Daily Deal Expires No
Unit Price No
Youtube Video No
Free Shipping? Yes
Free Shipping Qty Label No
Free Shipping Qty No
SKU: 5165448877

Questions and Answers

Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 55 questions Browse 55 questions and 131 answers
Can this be shipped to California?
Ed B on Jan 7, 2019
BEST ANSWER: NO!
When will this be back in stock?
Cade K on Nov 24, 2018
BEST ANSWER: It is now, my friend!
Can I use a suppressor with the rail on this build?
Travis C on Aug 26, 2018
BEST ANSWER: The PSA flash can has an o.d. of 1.20”. Measuring my PSA 12” mlok slant rail and anything larger then 1.20” might make contact while firing due to barrel whip and close tolerances. Most 5.56 rated suppressors are around 1.5” o.d. So in general I would say no a suppressor cannot be with this combination of a 10.5” barrel, and this particular 12” rail.
what is the the differance between 516 5448 877 and 516 5450 476?
shane r on Jan 31, 2019
PSA 10.5
PSA 10.5" Carbine-Length 5.56 NATO 1/7 Nitride 12" Slant M-Lok MOE EPT SBA3 Pistol Kit - 5165448877
PSA 10.5
PSA 10.5" Carbine-Length 5.56 NATO 1/7 Nitride 12" Slant M-Lok MOE EPT SBA3 Pistol Kit - 5165450476
BEST ANSWER: The difference is the rail. Get whichever rail is more aesthetically pleasing to you.
Does the build kit include everything for a stripped lower?
David S on Jul 30, 2018
BEST ANSWER: Absolutely! Only thing I added was a sling loop under the castle nut. Great kit and excellent trigger group.
Whats better. Pistol or carbine gas for the 10.5 kit?
jeremiah f on Aug 27, 2018
BEST ANSWER: The dwell time on the carbine length gas system is a little bit short with a 10.5" barrel; the dwell time on a pistol length gas system is a little bit long. I have not experienced any problems with my carbine length gas system and 10.5" barrel.
Can this item be shipped to Maryland ?
RyanB on Aug 7, 2018
BEST ANSWER: Yes I live in crisfield and I had my 14.5 shipped to my house. also if the item is restricted it will tell you once you add it to your shopping cart
When assembled, what is the overall length from the flash can to the back end of the buffer tube? To the back end of the brace when in the shortest position and longest position?
Frank G on Dec 3, 2018
BEST ANSWER: Someone posted a pic in the reviews. It looks like just over 28”
What is the overall weight of this upper setup?
Jonathan K on Sep 21, 2018
BEST ANSWER: Just under 7lbs.
What is the difference between the sku# ending in 5448807 VS.
sku# ending in 5448877...?
What am I missing?
D W on Jan 4, 2019
PSA 10.5
PSA 10.5" Carbine-Length 5.56 NATO 1/7 Nitride 12" Slant M-Lok MOE EPT SBA3 Pistol Kit - 5165448877
PSA 10.5
PSA 10.5" Carbine-Length 5.56 NATO 1/7 Nitride 12" Slant M-Lok MOE EPT SBA3 Pistol Kit - 5165448807
BEST ANSWER: One has a full rail on the handguard... The other has just thr rail at the front and back is all I can see...
Is the flash can “permanently fixed” (i.e. pinned and welded) to the barrel?
MacBean on Jan 1, 2019
BEST ANSWER: It is my understanding the flash can is screwed on. When the hand guard is removed the fully exposed can will be seen with two flat sides at it's rear. Connecting a wrench here should remove it. There are no welds at the rear of the can. I have not tried to remove mine. Looks cool and gives it a bull barrel look.
Will any lower work?
Raul M on Dec 7, 2018
BEST ANSWER: Mine’s sitting on an Anderson Manufacturing lower and so far it functions perfectly.
I can seem to locate the brand name for the barrel. Is it listed on here? If so what is the brand?
Braden S on Dec 4, 2018
BEST ANSWER: There are no markings indicating the barrel manufacturer. Just "300BLK 1/8".
Any idea when these will be back in stock?
Chunt on Feb 8, 2019
BEST ANSWER: Now, get them while they are hot!
What is the difference between this build kit and build kit with sku ending in 48807 ?
Robert C on Aug 13, 2019
If I have never built my own gun. How hard is it for someone that doesn’t know how and what exactly else will I need to buy ?
Ranger U on May 2, 2019
BEST ANSWER: It's very easy to build, (You Tube has thousands of regular people doing step by step video instructions. Watch a few of them to judge whether or not you'd feel comfortable doing it yourself).

For additional parts, you'll need the lower receiver, at least one magazine, and some type of aiming device, (Scope, Red Dot, Iron Sights)
Hi is this kit requires SBR from atf or Is this considered a pistol thank you ?
Christian on Jan 28, 2019
BEST ANSWER: If you're "intent" is to build a pistol, it's considered a pistol because of the SBA3 brace (Google SB Tactical ATF Letter). Keep in mind, it is all about "intent"; if you're "intent" is to bypass and use your pistol as an SBR, your "intent" makes it an SBR. This holds true from my research for all AR pistol builds.
What lower would you recommend?
Jonathan B on Aug 4, 2019
BEST ANSWER: I’ve had great luck with PSA stripped lowers and parts kits. When assembling a pistol make sure you are using a brand new lower or a dedicated pistol lower. Make sure you are aware of all local and federal laws prior to assembly.
Can. You shoot .223?
Fernando A on Jul 24, 2019
BEST ANSWER: Yes. Any weapon chambered for 5.56mm can shoot .223 Cal safely. Weapons chambered in .223 Cal CANNOT safely shoot 5.56mm.
Does the 21 OAL refer to the upper? Or the pistol in it’s completed form?
benjiman c on Mar 9, 2019
BEST ANSWER: Upper only you must purchase a stripped reciver and assemble it ! Also let your ffl you send reciver to that reciver is for multi use as your building a pistol build !
What are the necessary tools to put this build together?
Dylan H on Feb 5, 2019
BEST ANSWER: A set of roll pin punches, a vice, and a hammer with a polymer strike face and a brass strike face. Maybe some needle nose pliers. Three hands also helps.
Is the gas block adjustable?
Harrison on Jul 2, 2019
BEST ANSWER: No
Is this handguard a free float hand guard?
Robert L on May 27, 2019
BEST ANSWER: It is.
Can this be bought in store?
Corey R on Mar 22, 2019
BEST ANSWER: Possibly, but this can be shipped to your door. All you need to pick up from the store is the lower. I love mine.
What is the difference between this kit and the seemingly identical kit with the sku ending with 807 instead of 877?
Mike D on Jan 1, 2019
BEST ANSWER: One model has picitinny rail on top of the free float all the way down. The other only has picitinny on top at the front of the rail where you would put your front sight. Personally, I bought the full length picitinny rail so I could mount a peq box on top. Other wise you have to mount accessories with mlok
Does this kit come with a rear takedown pin detent that is threaded for a 4-40 set screw ? The lower that I want to use with this kit calls for a 4-40 set screw.
Roland G on Dec 6, 2018
BEST ANSWER: This is a standard lower parts kit. If you’re lower has different specs you may have to buy that set screw
Does this require an nfa tax stamp?
Jordan H on Aug 15, 2019
BEST ANSWER: Hello,

When assembled with the included parts it is considered a pistol and does not require an ATF Stamp. It is the customer's responsibility to be aware of all applicable laws and regulations regarding the purchase and ownership of uppers with a barrel length of less than 16". Federal NFA regulations are applicable to this item.

Best Regards,
(Name of Employee Removed)
Palmetto State Armory Customer Service
Just to confirm-i can replace the buffer and spring with a standard carbine buffer and spring correct? not a pistol version. thx
james m on Jul 28, 2019
BEST ANSWER: That is correct. Without going and looking at mine, I’m 99% sure it comes with the standard carbone buffer and spring.
What are the holes on the rear of the hand guard used for? The ones left and right of the chamber. They are about 3/8”.
John R on Jul 27, 2019
BEST ANSWER: They are attachment points for a Quick Detach (QD) sling swivel.
should the flash can rest on the handguard or not be touching? if its touching how fix this?
james m on Jul 27, 2019
BEST ANSWER: Should not touch, there Should be Clarence all the way around sounds like maybe the handguard got bent down with a little bit

Reviews

4.7 / 5.0
168 Reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
141
18
3
4
2
Very easy to put together works great
May 18, 2020
Purchased
2 months ago
Shoots great!
I'm very happy with this kit. It went together great on my Aero lower. Shoots awesome with no issues.
April 23, 2020
Purchased
2 months ago
Great Buy!!!
Great gun, easy to assembly. This was the first AR I ever put together and it took about 1.5 hrs max!. I will definitely be buying more..
April 14, 2020
My first pistol didn’t disappoint!
Nice small profile, finish and feel is top notch. I slapped her in a home mill and it’s great! I’m not gonna say I tested fired it by way of mag dump cause that’s just silly... but I did. and she loved it 🇺🇸
I fully trust this little sweetie to scream whenever I say so, we gonna get along just fine 😏
User submitted image
User submitted image
April 8, 2020
Purchased
10 months ago
Very impressed
Very happy with the quality of this kit. Especially the trigger. The ept trigger is much nicer than I expected As always parts go together with no issues. Great bang for the buck
User submitted image
Added Feb 25, 2020
February 25, 2020
Purchased
5 months ago
Very Happy
So, Even though this is my first build, I have been shooting AR platforms for well over 30 years now. I have to say that the quality of this product is first rate and would recommend this for anyone interested in a build of their own. I have read through some of the other reviews and noticed that some are not so good but overwhelmingly most are good. Here is what I have to say to that. Just like with cars, there is always going to be a lemon out there. When you get this kit I recommend that you thoroughly inspect it front to back as you put it together. If you discover what you believe is an issue, give the customer service a chance to make it right. Additionally, make sure you clean and lube everything properly before you go to the range for the first time. Remember, ARs by nature have tight tolerances and like to run wet. Additionally, remember that every time it fires, it is producing around 30,000 psi of pressure on the system, so, making sure you have it done right before you hit the range is extremely important. Again, I am very happy with how this turned out and would recommend this kit to anyone who wants to venture into the build your own world.
January 24, 2020
Ar pistol build
Everything I needed to complete my pistol build in one kit. Very impressed with the quality and how easy this made my project.
December 23, 2019
Purchased
6 months ago
The finish on the upper is nice everything is well made. it installed nicely on my lower, I was missing a trigger assembly pin but I emailed them and they mailed me a new set right away.
December 20, 2019
Purchased
6 months ago
Great product.
I love this kit. Roughly 400 rounds so far with no issues other than a bad magazine I tried. It is very light weight and a lot of fun to shoot. I'll probably get another one away some point.
November 21, 2019
Purchased
8 months ago
Great kit.
Definitely recommend this kit. Fit and function are flawless. Mated well with 80% lowers. I purchased 3 kits total- and with ~ 500 rds through each, I've had zero malfunctions.
November 20, 2019
Purchased
8 months ago

Customers Who Viewed This Item Also Viewed