Palmetto State Armory AR-15 Classic LPK w/o Fire Control Group - 1785

Everything fit great in my lower and for good price.

Poor quality pins and the wrong size.

This lower parts kit fit perfectly in my Anderson lower. All parts were nicely finished. I would definitely recommend this kit to anyone. Shipping was quicker than expected but that is a good thing. Will buy again.

Perfect LPK for a drop in trigger.

I have purchased many classic LPKs. I was really surprised with my last order. Just not the quality I was used to seeing.

I bought 3 of these. My experience in the past has always been good. Not this time. The lpk kit is below sub par. Really sad. I have always given them 5 stars for this kit and have bought many. But these kits were not the same quality. Definitely using the lowest bidder parts.

Everything went together fine but the bolt catch was a little stiff using an Anderson lower. I removed the bolt catch (looks cast) polished it with a jewelers file where it was binding and reinstalled it. Gtg.

I'd buy more just check function thoroughly before driving the pins home...

Just wait until it's $29 instead of $39 to buy it. Luck of the draw.....

After reading several reviews on this kit I decided to pull the trigger on it. Once I received the kit the first thing that I noticed is the pins that hold the take down pins in place were steel not brass like pictured this makes the take down pins very hard to push/pull and gritty to the point that you almost need a punch. The pins are also not uniform on ends so on take down pin works better then the other. After getting most of the lower assembled I came to the trigger and safety; this being a build I ordered a drop in trigger that didn't come with tigger pins (the two that have ordered in the past haven't) but the LPK did not either now I have to make a trip to gunsmith to get trigger pins. Other then those few things the kit went together fine but for future builds I might look elsewhere. Shipping was fast and fee this was defiantly a plus.

Springs detents buffer retainer selector and mag release assembly are are all good.

Very good: pistol grip screw uses an Allen head instead of a flat head. If you don't have a long or T-handle Allen key go get one.

Gripes: 1) the part of the pistol grip that engages the lower receiver is bent together making for a very tight fit that doesn't quite go flush to the receiver. I'll likely replace this anyway so I don't really care. 2) the roll pins do not have a bevel to help start them. This made the bolt catch roll pin installation particularly challenging.

For $30 I am not complaining. The last LPK I used ($60 Colt pack) seemed to have a lot nicer fit and finish but not twice as nice and nothing that would impact function or reliability.

so i installed this kit into a bushmaster lower. its not my first ar but it is the first lower i built. i had it together in about 45 mins while watching instructional youtube vids. everything went together flawlessly and works perfectly. the only thing that seemed funky was the pistol grip. the top corners that slide up onto the lower receiver were pinched together slightly instead of being straight and it took a lot more fiddling to get it on then it should. other grips ive mounted (magpul mft) seem to fit a little nicer. either way it just means it fits very tightly which isnt exactly a bad thing.

It's all you need to put your lower together minus the trigger and buffer parts at a great price. High quality no issues with installation and use a little grease/oil and you are good to go. No need to pay high dollar prices for "boutique names" stuff just works and functions flawless. Have used 5 or 6 thus far I wait for the specials and buy a couple or more when needed. Great service from PSA all the time buy with confidence. Have also paid much more for "similar" products from other places and it was just a waste of money but needed the stuff in a jamb.

I received my order of this lpk and everything went together well and was packaged great springs in one bag etc. But I went to put the pistol grip on and the screw and the washer together. Well I tighten it up all the way and the grip had at least a 1/8 inch wobble to it. I fixed by adding another thicker washer to it. Other then great.

Great kit at a great price!